Results 1 to 6 of 6

Thread: Simple Mouse Smart card programmer.

  1. #1
    Super Moderator aamir11's Avatar
    Join Date
    Jul 2008
    Location
    Asia
    Posts
    7,488
    Rep Power
    421

    hot Simple Mouse Smart card programmer.

    Simple Mouse Smart card programmer.

    This "SimpleMouse" Smartcardprogrammer can be used to read and write most of all async - Smartcards (Processorcards), including the new "Hornet and +1" DPSC΄s in update and reprogramming mode.

    It is jumper-selectable in either Smartmouse or Phoenix Mode (Reset active hi or low) and Jumper selectable for 3.57 and 6 MHz


    The "original" Smartmouse gets its power out of the serial port of the Hostcomputer - in this design this "feature" is not implemented because the Hostcomputer can only deliver about 15 mA to the Programmer. This is not enough for older Smartcards. So this design uses an 9V Alkaline Battery 6LR61.

    To make this design cheap there are no gimmicks like flashing diodes or expensive connectors and switches. You have to solder the 9 or 25 pin serial cable directly the corresponding pads of the PCB.




    ++++++++++++

    There is an new/other Layout included. It has some 100R Resistors in
    the connections to the smartcard, to limit the current in the case
    of malfunction of the software. Furthermore the Layout is a litte more
    easier to build at home because the distance between the tracks is
    bigger....

    All the following description is also usable for the new layout. Some
    changes in the partvalues have to be taken directly out of the Top1.gif.
    The LEDs schould be LowPower....




    ++++++++++++

    JUMPERS

    SIP1 is for selecting the Clockrate 3.57 or 6MHz

    SIP 1

    Shorting pin 1 + 2 -> 3.57 MHz
    Shorting pin 2 + 3 -> 6 MHz


    SIP2 is for selecting the type of mode (Smartmouse or Phoenix)

    SIP 2

    Shorting pin 1 + 2 -> Smartmouse
    Shorting pin 2 + 3 -> Phoenix

    SIP3

    SIP3 is a Jumperblock which is used as a "Switch" to turn the Battery
    on an off - or as the connector for an external DC-powersupply.

    Shorting pin 1+2 -> Power off
    Shorting pin 2+3 -> Power on

    Without Jumper you can connect an external DC-Powersupply to this Header:
    Pin1 -> GND
    Pin2 -> 9 to 15 Vdc
    Pin3 -> left open


    SIP4

    SIP3 is΄nt really a Jumperblock it is the connection to the serial
    Port of the Hostcomputer.


    SIP4 9Pin SubD Serial port cable

    Pin1 -> Pin 5
    Pin2 -> Pin 2
    Pin3 -> Pin 3
    Pin4 -> Pin 1
    Pin5 -> Pin 7


    PART LIST



    ID Comment

    BT1 9V Block Alkaline
    C1 22pF RM 5 Keramik
    C2 22pF RM 5 Keramik
    C3 22pF RM 5 Keramik
    C4 22pF RM 5 Keramik
    C5 100nF RM 5 KDPU
    C6 100nF RM 5 KDPU
    C7 1uF RM 2.5 Tantal
    C8 1uF RM 2.5 Tantal
    C9 1uF RM 2.5 Tantal
    C10 1uF RM 2.5 Tantal
    C11 1u RM 2.5 Tantal
    C12 100nF RM 5 KDPU
    C13 100nF RM 5 KDPU
    C14 47pF RM 5 Keramik
    C15 1uF RM 2.5 Tantal
    D1 BAT41 or BAT48 Shottky!!
    D2 1N4148
    LD1 LED 3mm red Low Power
    R1 1M RM 5 Bauform 02/04 1/10W
    R2 2K2 RM 5 Bauform 02/04 1/10W
    R3 1M RM 5 Bauform 02/04 1/10W
    R4 2K2 RM 5 Bauform 02/04 1/10W
    R5 2K2 RM 5 Bauform 02/04 1/10W
    R6 2K2 RM 5 Bauform 02/04 1/10W
    R7 10K RM 5 Bauform 02/04 1/10W
    SC1 Smartcard Adapter Amphenol Switch opens when Card is inserted!
    SIP1 Jumperblock 3Pin
    SIP2 Jumperblock 3Pin
    SIP3 Jumperblock 3Pin
    SIP4 Jumperblock 5Pin
    U1 74HC00
    U2 MAX 232
    U3 78L05
    X1 3.57MHz HC18/U
    X2 6MHz HC18/U

    All Rs are 1/10W 4mm for laying mount or 1/4 W for standing mount.

    REMARKS

    It is very important for this design to use a Shottky diode for D1.
    Any other type will definitely NOT work!
    Look for the right polarity of the tantalum condensators! The
    MAX232 includes a so called chargepump and generates positive an
    negative Voltages respect to ground. So it is possible that the
    positive pole of an condensator is connected to ground - this is
    NOT wrong!

    For Mounting the Battery and fasten the serial cabel drill bigger
    holes at the corresponding points and use cablestrips.

    The enclosed Tiff΄s have a resolution of 400 dpi.
    ++++++++++++++++++


    Attached Files Attached Files

  2. #2
    Security Administrator MikroTik's Avatar
    Join Date
    Nov 2007
    Location
    Lesotho
    Posts
    6,793
    Rep Power
    424

    Re: Simple Mouse Smart card programmer.

    Looks good, only thing is I don't see the schematic diagram nor the component overlay, maybe I am missing something.
    Press if you find post usefull.
    Use "SEARCH" Before Posting, Post In Correct Sections, Respect Other Members.
    AND ALWAYS REMEMBER... FOLLOW !!

  3. #3
    Super Moderator aamir11's Avatar
    Join Date
    Jul 2008
    Location
    Asia
    Posts
    7,488
    Rep Power
    421

    Arrow Re: Simple Mouse Smart card programmer.

    Phoenix interface

    It is an interface used for communication a PC with a smartcard . The Phoenix interface can also be used to update the EEPROM 24(L)C16 on the Multimac II cards (gold wafer cards). This interface require a separate power supply (9 - 30V). Connection with the PC serial port is made by cable 1-1, 9pin connectors, male-female.

    List of components:
    -------------------
    1 x slot for ISO card (eight pins are enough)
    1 x female 9pin connector RS232
    1 x MAX232
    1 x 7805 (78L05)
    1 x 74LS07 (7407)
    1 x 74HC04
    1 x LED green
    1 x LED red
    5 x capacitor 4u7/16V (2u2-22u/16-63V)
    1 x capacitor 100nF
    1 x capacitor 100pF
    2 x capacitor 27pF
    2 x resistor 220R
    2 x resistor 2K2
    1 x resistor 22K
    1 x resistor 1M0
    1 x crystal 3.579545 MHz


    SimplePhoenix


    It is a simple variant of SmartMouse which can be used as Phoenix interface. This SimplePhoenix together with StupidPipo and Jupiter Card programmer is able to program Gold Wafer Cards, Jupiter Cards and Fun Cards.
    This interface require a separate power supply (9 - 30V). Connection with the PC serial port is made by cable 1-1, 9pin connectors, male-female.

    List of components
    -------------------
    2 x capacitor 22pF
    1 x capacitor 47pF
    3 x capacitor 100nF
    5 x capacitor 4,7uF/16V (1uF-22uF/16-63V)
    2 x resistor 1K0
    1 x resistor 2K2
    1 x resistor 10K
    2 x resistor 1M0
    1 x 1N4148
    1 x BAT41 or BAT48, Shottky!!
    2 x green LED, 3mm "Low Power"
    1 x 74HC00
    1 x MAX 232
    1 x 78L05
    1 x female 9pin connector RS232
    1 x slot for ISO card (eight pins are enough)
    1 x crystal 3.579545 MHz


    SmartMouse

    Two version of SmartMouse are presented - (A) and (B).
    (A) without data LED and protective resistors.
    (B) with LED and protective resistors.

    The interface can also be used as Phoenix to update the EEPROM 24(L)C16 on the Multimac II cards (gold wafer cards) or as SmartMouse to update original ****** cards. This interface require a separate power supply (9 - 30V). Connection with the PC serial port is made by cable 1-1, 9pin connectors, male-female.

    List of components - SmartMouse A:
    --------------------------------------
    4 x capacitor 22pF
    1 x capacitor 47pF
    3 x capacitor 100nF
    5 x capacitor 2,2uF/16V (1uF-22uF/16-63V)
    4 x resistor 2K2
    1 x resistor 10K
    2 x resistor 1M0
    1 x 1N4148
    1 x BAT41 or BAT48, Shottky!!
    1 x green LED, 3mm "Low Power"
    1 x 74HC00
    1 x MAX 232
    1 x 78L05
    2 x single switch on-on
    1 x female 9pin connector RS232
    1 x slot for ISO card (eight pins are enough)
    1 x crystal 3.579545 MHz
    1 x crystal 6MHz

    List of components - SmartMouse B:
    --------------------------------------
    4 x capacitor 22pF
    1 x capacitor 47pF
    3 x capacitor 100nF
    5 x capacitor 4,7uF/16V (1uF-22uF/16-63V)
    1 x resistor 10R
    3 x resistor 100R
    4 x resistor 1K0
    2 x resistor 2K2
    1 x resistor 4K7
    2 x resistor 1M0
    1 x 1N4148
    1 x BAT41 or BAT48, Shottky!!
    3 x green LED, 3mm "Low Power"
    1 x 74HC00
    1 x MAX 232
    1 x 78L05
    2 x single switch on-on
    1 x female 9pin connector RS232
    1 x slot for ISO card (eight pins are enough)
    1 x crystal 3.579545 MHz
    1 x crystal 6MHz



    Attached Files Attached Files

  4. #4
    Security Administrator MikroTik's Avatar
    Join Date
    Nov 2007
    Location
    Lesotho
    Posts
    6,793
    Rep Power
    424

    Re: Simple Mouse Smart card programmer.

    This is exactly the one I constructed many years ago, thanks aamir11, I still have spare Xtals left over.
    Regards
    Press if you find post usefull.
    Use "SEARCH" Before Posting, Post In Correct Sections, Respect Other Members.
    AND ALWAYS REMEMBER... FOLLOW !!

  5. #5
    New Member
    Join Date
    Sep 2013
    Location
    mexico
    Age
    49
    Posts
    7
    Rep Power
    0

    Re: Simple Mouse Smart card programmer.

    i cant download..no exist file!!

  6. #6
    Administrator THE BOSS's Avatar
    Join Date
    May 2006
    Location
    MVDIG
    Posts
    3,973
    Rep Power
    369

    Re: Simple Mouse Smart card programmer.

    all files removed from server as it was very old file -thread closed
    Quote Originally Posted by lobitoferoz View Post
    i cant download..no exist file!!

Similar Threads

  1. Replies: 1
    Last Post: 13-11-2009, 12:33 PM
  2. Replies: 0
    Last Post: 13-11-2009, 10:29 AM
  3. gamma smart card
    By makistov in forum CardSharing Chat
    Replies: 6
    Last Post: 20-10-2009, 05:32 PM
  4. gamma card programmer usb only
    By christosg26 in forum GammaCard !
    Replies: 4
    Last Post: 26-08-2009, 09:04 PM
  5. ******** New Smart Card
    By mvdig in forum Announcements and News
    Replies: 0
    Last Post: 15-09-2006, 02:43 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •